Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The author is making a few good points regarding Tools You Need to Install a New Bathtub as a whole in this post in the next paragraphs.
Mounting a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult job. If the old tub is easily accessible, the job can move immediately; if you have to open a wall to get rid of the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. Make sure you have actually certified yourself for the work as well as fit attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to take into consideration using one before you start. Chances are you may require a specialist plumber to make tube links.
This write-up will assist you install a new bathtub in your restroom if you have actually currently acquired a brand-new tub as well as do not require to alter the setup of your previous water supply pipes.
Your devices and also product checklist should make up the following:
Preparing for the Installation
To start with, the sustaining frame provided with the bathroom must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Using the two wood boards under its feet, place the bath tub in the called for placement. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the bath tub up until the level checks out degree.
To set up taps, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water as well as check all joints as well as new pipework for leakages and tighten them if necessary. Load the bath tub and also examine the overflow outlet and also the normal outlet for leaks.
Lastly, repair the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the tub has actually been utilized at least when as this will settle it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in location between the tap and the sink. Protect the faucet in place with the supplier provided backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and fittings. They are sold in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the tub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that post on Installing A Bathtub when doing research the web. Enjoyed reading our blog entry? Please share it. Help another person check it out. Thanks a lot for your time. Visit again soon.
Book Now! Report this page